Welcome to the TMA - the Traditional Muzzleloading Association
The TMA is always free to access: totally non-profit and therefore no nagging for your money, no sponsors means no endless array of ads to wade through, and no "membership fees" ever required. Brought to you by traditional muzzleloaders with decades of wisdom in weaponry, accoutrements, and along with 18th and 19th century history knowledge of those times during the birth our nation, the United States of America.
If you are a current TMA Contributing Member you MUST click HERE - IMPORTANT!


« previous next »
Pages: 1 2 [3]

Author Topic: TOTW Flint Flush  (Read 6853 times)

Offline mehavey

Re: TOTW Flint Flush
« Reply #30 on: August 26, 2014, 12:38:39 AM »
"Swab" cleaning with a sealed bore (toothpick in vent) is
always an option, but any hydraulic pressure created by
having actual fluid in that bore will blow the toothpick out.

Actual "flush" cleaning requires fluid flow that can only be
obtained by pulling the barrel entirely, or by a clamp/tube
assembly such as the TOTW flush clamp.
Logged

Offline Kermit

  • TMA Forum Member
  • ***
  • Posts: 421
  • Total likes: 0
  • TMA: 3/21/17 ~ 3/21/18
  • TMA Member: 393
Re: TOTW Flint Flush
« Reply #31 on: September 10, 2014, 02:58:13 PM »
Mine works on about half my flintlocks. On some guns the wood on the off side prevents aligning the gizmo squarely and over the vent. I don't use it any more. Toothpicks and water now. There are a lot of cutsie ideas out there that make sorta sense when you buy them, but later they prove merely to be a means of extracting money from your wallet. It's happened to me once or twice.
Logged
"Anything worth doing is worth doing slowly."
Mae West

Member Number 393

Offline mehavey

Re: TOTW Flint Flush
« Reply #32 on: September 10, 2014, 03:38:44 PM »
Doe yours have the knurled nut right next to the O-ring -- so that you can effectively
push the O-ring further forward -- and effectively seal even an offset interface/joint ?
« Last Edit: September 10, 2014, 03:57:34 PM by mehavey »
Logged

Offline francois labiche

Re: TOTW Flint Flush
« Reply #33 on: September 10, 2014, 03:51:52 PM »
Mine leaks, so I no longer try to use it. Tooth picks are cheap and do the the job. I pull the lock insert toothpick, fill bore with warm soapy water and stand gun in corner outside while i go and clean the lock. Afterwards dump the water and swab until dry. That process has worked for me for years. A bottom scraper is a better investment.
F.
Logged

Offline mehavey

Re: TOTW Flint Flush
« Reply #34 on: September 10, 2014, 04:01:48 PM »
Quote
A bottom scraper is a better investment...
Got one.  The ability to simply stutter-pump the last 6" of a barrel to flush out the bottom of a patent breech makes the pain of cleanup -- even with a scraper -- go completely away.

Patent breech patch come out spotless first time.
Logged

Offline Geezer in NH

Re: TOTW Flint Flush
« Reply #35 on: September 10, 2014, 11:05:04 PM »
Quote from: "Dewey"
Toothpicks are cheap .....
Bingo!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Logged

Offline Geezer in NH

Re: TOTW Flint Flush
« Reply #36 on: September 10, 2014, 11:07:19 PM »
Quote from: mehavey
"Swab" cleaning with a sealed bore (toothpick in vent) is
always an option, but any hydraulic pressure created by
having actual fluid in that bore will blow the toothpick out.

quote] 30 years of flintlock cleaning and never had a blowout but then What's the big deal if one got one?
Logged

Offline ron wilkerson

Re: TOTW Flint Flush
« Reply #37 on: September 12, 2014, 01:11:51 PM »
Been using one for several years now myself. I change my o-ring every once in a while. It works good for me.
Logged
Pages: 1 2 [3]
« previous next »