Your TMA Officers and Board of Directors
Support the TMA! ~ Traditional Muzzleloaders ~ The TMA is here for YOU!
*** JOIN in on the TMA 2024 POSTAL MATCH *** it's FREE for ALL !

For TMA related products, please check out the new TMA Store !

The Flintlock Paper

*** Folk Firearms Collective Videos ***



« previous next »
Pages: [1]

Author Topic: Knapping hammer?  (Read 1168 times)

Offline daddywpb

  • TMA Forum Member
  • ***
  • Posts: 15
Knapping hammer?
« on: January 25, 2011, 06:10:15 PM »
Just wondering if I need one? Are they fairly easy to use? Just lloking for advise from some shooters in the know. Thanks!
Logged
Member Number 605
Expires 01/23/2012

Offline david32cal

  • TMA Forum Member
  • ***
  • Posts: 421
(No subject)
« Reply #1 on: January 25, 2011, 06:49:37 PM »
i just use the back edge of my knife
Logged
"The reason a dog has so many friends,He wags his tail instead of his tongue"

Offline Captchee

  • TMA Forum Member
  • ***
  • Posts: 6215
(No subject)
« Reply #2 on: January 25, 2011, 08:09:26 PM »
or you can pick up a cheep brass hammer and screw driver set .
Logged

Offline daddywpb

  • TMA Forum Member
  • ***
  • Posts: 15
(No subject)
« Reply #3 on: January 25, 2011, 08:12:54 PM »
Quote from: "Captchee"
or you can pick up a cheep brass hammer and screw driver set .

It is to put the sharp edge back on the flint when it gets worn?
Logged
Member Number 605
Expires 01/23/2012

Offline Captchee

  • TMA Forum Member
  • ***
  • Posts: 6215
(No subject)
« Reply #4 on: January 25, 2011, 08:20:35 PM »
Yep you will need something to touch up the flint . Be it your knife , a small hammer or a set of Knapping pliers
 
 i used to get those  cheep hammer sets at the dollar store.
 They are really brass coated  but I have not had one wear out.
 They are bigger then whats sold as Knapping hammers .
 They work better for me .
Logged

Offline Kermit

  • TMA Forum Member
  • ***
  • Posts: 421
  • TMA: 3/21/17 ~ 3/21/18
  • TMA Member: 393
(No subject)
« Reply #5 on: February 09, 2011, 10:16:02 PM »
I've seen guys pressure flake a new edge with the tip of an antler tine. Also seen it done with a little pointed copper tool. I use either a wee brass hammer or the back of my knife. I do it at full cock with my left index finger supporting the underside of the flint's edge, then tapping it on the top side. Knocks ittybitty flakes off the lower side.
Logged
"Anything worth doing is worth doing slowly."
Mae West

Member Number 393

Offline B.Habermehl

  • TMA Forum Member
  • ***
  • Posts: 6
(No subject)
« Reply #6 on: February 17, 2011, 09:02:29 PM »
I use my turn screw.  I hold my finger under the edge of the flint.  putting the edge of the turn screw about 1/32 or less from the edge of the flint, then tap the turn screw.  It takes just a little practice, then you will be able to drive off really small shards of flint, bringing the flint to a razor sharp edge. I for one can't do any thing with a knapping hammer. This can also be done with a nail with a step filed in or a piece of brass used as a punch. bjh
Logged

Offline Dphariss

  • TMA Forum Member
  • ***
  • Posts: 19
Re: Knapping hammer?
« Reply #7 on: February 20, 2011, 02:23:09 AM »
Quote from: "daddywpb"
Just wondering if I need one? Are they fairly easy to use? Just lloking for advise from some shooters in the know. Thanks!

Back of my knife. I have used the heavy brass adjustable measure too.

Dan
Logged

Offline smokinbuck

  • TMA Forum Member
  • ***
  • Posts: 8
(No subject)
« Reply #8 on: February 20, 2011, 04:36:34 PM »
The back of a knife blade can be dangerous in that the steel on the flint will spark. Loaded pan or not I wouldn't want a spark dancing around. I use a brass hammer sometimes but have made knapping hammers out of brass door hinge pins. Mount them in a piece of antler and they work just fine. Look good too.
Mark
Logged

Offline Loyalist Dave

  • TMA Forum Member
  • ***
  • Posts: 687
  • TMA Member: 800
  • Location: MD
(No subject)
« Reply #9 on: February 20, 2011, 05:52:49 PM »
I have three brass knapping hammers, but for some reason I always use the back of my knife, so I don't worry about the hammers any more.  

LD
Logged
It's not what you think you know; it's what you can prove.

Offline greyhunter

  • TMA Forum Member
  • ***
  • Posts: 1491
  • TMA Member: Membership #291, Expires 2/11/2019
(No subject)
« Reply #10 on: February 20, 2011, 08:26:10 PM »
At our BP shoots I have used my gerber multi tool many times for dull flints, removing locks, etc. etc. Stainless steel, not pc but a real handy do all tool. Gotta keep those boys shootin!
Logged
Pa. TMA State Representative.[/color]
Member#291  2/11/19

Offline Kermit

  • TMA Forum Member
  • ***
  • Posts: 421
  • TMA: 3/21/17 ~ 3/21/18
  • TMA Member: 393
(No subject)
« Reply #11 on: February 20, 2011, 09:30:50 PM »
About that knife sparking? Never knap a flint that way in a loaded gun. I've seen folks do it, but that's when brass should be used, and you empty the pan first, and keep it pointed downrange.
Logged
"Anything worth doing is worth doing slowly."
Mae West

Member Number 393

Offline smokinbuck

  • TMA Forum Member
  • ***
  • Posts: 8
(No subject)
« Reply #12 on: February 20, 2011, 11:56:34 PM »
I obviously agree fully with Kermit. There is first hand knowledge of a spark in an empty pan finding it's way into a touch hole and igniting the main charge.
Mark
Logged

Online BEAVERMAN

  • TMA Contributing Member
  • ***
  • Posts: 6039
  • TMA: TMA Vice President
  • TMA Member: Charter Member #145
  • Location: Vaughn, WA
(No subject)
« Reply #13 on: February 21, 2011, 10:34:15 AM »
I use the one I had wally here on the forum make for me, the hammer that he makes with his flint set is my design and it works well!
Logged
Jim Smith
TMA Vice President
Charter Member #145  EXPIRATION 1/21/25
Green River Mountain Men
Peninsula Longrifles
WSMA
U.S.M.C.
BSA                    
Save America. Spay or neuter a liberal today.

"An armed man is a citizen,..an unarmed man is a subject!"
Pages: [1]
« previous next »