Your TMA Officers and Board of Directors
Support the TMA! ~ Traditional Muzzleloaders ~ The TMA is here for YOU!
*** JOIN in on the TMA 2024 POSTAL MATCH *** it's FREE for ALL !

For TMA related products, please check out the new TMA Store !

The Flintlock Paper

*** Folk Firearms Collective Videos ***



Author Topic: Bone Buttons  (Read 3737 times)

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Bone Buttons
« on: March 06, 2014, 07:48:28 PM »
I have been thinking about making a couple of bone buttons for a sewing kit that I am making.
So while at Petco I saw some beef rib bone chews, one made the trek to my camp.

So is there any tricks to make said buttons, or anything that I should watch out for.
In my thinking wash with hot soapy water and dry. Draw a circle and cut out. Drill a couple holes there about the center. Maybe dress with bee's wax.

Any other info or suggestions  would be a help.

LeeRoy
Keep your powder dry.

Online sse

  • TMA Contributing Member
  • ***
  • Posts: 5373
  • TMA Founder
  • TMA: TMA Co-Founder, Charter Member, BoD.
  • TMA Member: Charter Member #3
Re: Bone Buttons
« Reply #1 on: March 06, 2014, 10:59:04 PM »
I can't answer your question, but it sounds like a nice project and I hope it works out well (and would like to see pics of the outcome).
Regards, sse

************
Consider joining the TMA...If you're not a member, you're missing out...

TMA Member #3
Exp. July A.D. 1825


Offline Woodrock

  • TMA Forum Member
  • ***
  • Posts: 45
Re: Bone Buttons
« Reply #2 on: March 10, 2014, 12:59:44 AM »
Most early bone buttons had a rounded depression in the centre. You can do this with a drill bit ground to the rounded shape. than cut out the button with a hole saw. Bone being fairly soft, you can make you own small hole saws from steel tubing with hand filed teeth.  I found it easier to centre the buttons by drill the thread holes after  cutting the depression, and making a jig with two pins to hold the blank in place whilst cutting out the button with the hollow bit. (hole saw).
Woody

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Re: Bone Buttons
« Reply #3 on: March 10, 2014, 08:44:48 AM »
Thanks for the replies.

LeeRoy
Keep your powder dry.

Offline LRB

  • TMA Forum Member
  • ***
  • Posts: 137
Re: Bone Buttons
« Reply #4 on: March 10, 2014, 01:22:37 PM »
Most early buttons were also 4 holers. Not all, but most.

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Re: Bone Buttons
« Reply #5 on: March 12, 2014, 08:45:30 PM »
Wouldn't you know it, I split the rib bone down both sides and remover the material from the inside. Now with 2 pieces of some what flat bone, they are too thin for buttons.

Next idea, thread winders. But the bone pieces are not truly flat.

Could these pieces be flattened?

Would placing them in hot water and then clamp them between something, to keep them flat until they cool work?

Any input would be helpful.

LeeRoy
Keep your powder dry.

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Re: Bone Buttons
« Reply #6 on: March 19, 2014, 07:37:30 AM »
Here is the end product of the rib bone. I made some thread winders for my sewing kit, husiff, housewife kit.
A item to carry in my new possibles pouch.

LeeRoy
Keep your powder dry.

Offline Roaddog

  • TMA Forum Member
  • ***
  • Posts: 1580
  • TMA Member: TMA Paid Member # 247 Expires 3/15 / 2019
Re: Bone Buttons
« Reply #7 on: March 20, 2014, 06:01:17 AM »
They look good Leeroy.Ihope you use a good dust mask wen working with bone.the dust can get in your lunges and will make you so ill that you won't get over it.
Minnesota TMA State Representative

Member #247

Offline Roaddog

  • TMA Forum Member
  • ***
  • Posts: 1580
  • TMA Member: TMA Paid Member # 247 Expires 3/15 / 2019
Re: Bone Buttons
« Reply #8 on: March 20, 2014, 06:03:04 AM »
Quote from: "Roaddog"
They look good Leeroy.I hope you use a good dust mask wen working with bone.the dust can get in your lunges and will make you so ill that you won't get over it.
Minnesota TMA State Representative

Member #247

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Re: Bone Buttons
« Reply #9 on: March 20, 2014, 10:07:29 PM »
Thanks for replying and the warning.
Yes, I use the 3-M paper mask that has the 2 straps. I use them when working with a sander too.

LeeRoy
Keep your powder dry.

Offline Roaddog

  • TMA Forum Member
  • ***
  • Posts: 1580
  • TMA Member: TMA Paid Member # 247 Expires 3/15 / 2019
Re: Bone Buttons
« Reply #10 on: March 21, 2014, 07:04:13 AM »
:hairy
Minnesota TMA State Representative

Member #247

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Re: Bone Buttons
« Reply #11 on: March 26, 2014, 08:58:03 AM »
Thanks for the replies.

I am thinking on another visit to PetMart, I will find a thicker piece of bone this time.

LeeRoy
Keep your powder dry.

Offline Ironhand

  • TMA Forum Member
  • ***
  • Posts: 242
  • TMA Member: Supporting Member # 664, Expiration 5/4/2019
Re: Bone Buttons
« Reply #12 on: March 26, 2014, 09:09:55 AM »
Talk to a butcher. Ask for a scapula (shoulder bone), they are fairly flat and have no marrow cavity.

Ironhand
Place your clothes and your weapons where you can find them in the dark.

   Lazarus Long

Offline LeeRoy

  • TMA Forum Member
  • ***
  • Posts: 33
Re: Bone Buttons
« Reply #13 on: March 27, 2014, 07:33:45 AM »
Thanks for the tip.

LeeRoy
Keep your powder dry.

Offline Loyalist Dave

  • TMA Forum Member
  • ***
  • Posts: 687
  • TMA Member: 800
  • Location: MD
Re: Bone Buttons
« Reply #14 on: January 16, 2015, 07:44:13 AM »
Quote from: "LRB"
Most early buttons were also 4 holers. Not all, but most.

They were?

 :cry:

LD
It's not what you think you know; it's what you can prove.